Patio Screen Cage with Hip Roof (Project #3343) – Palm Frond Dr, Punta Gorda, FL
This Punta Gorda patio screen cage covers a 15 × 18 ft patio with a bronze aluminum frame, a hip roof, and No-See-Um screen. It stands about 11 ft high, rests on a new concrete footing, and uses 2 × 5 SMB beams and a 5-inch Super Gutter. The permit stage took 2 weeks, and the work took about 3 weeks.
Project Overview
At a home on Palm Frond Dr in Punta Gorda, the homeowners wanted a screened space on their back patio. Project #3343 added a new patio screen cage that is 15 ft wide and 18 ft deep, with a footprint of about 270 sq. ft. The frame is bronze aluminum, and the structure stands about 11 ft high, with 9 ft walls.
A hip roof covers the cage and rises about 2 ft above the walls, which adds headroom in the center. The roof frame uses 2 × 5 SMB beams, and 2 × 4 patio members frame the walls and the roof. Before the aluminum went up, our crew excavated a trench along the cage line, set the reinforcing steel, and built a new concrete footing to carry the frame.
A 5-inch Super Gutter runs along the house wall and carries rain away through a downpipe with a splash block. One access door with an 8-inch kick plate and bronze hardware gives the family a way in and out, and the posts, beams, and door share one bronze finish.
No-See-Um 20/20 mesh covers the walls and the roof. Its finer weave keeps out small biting insects while still letting air and daylight through. Every property needs its own measurements and estimate, so the figures here describe this installation only.
Homeowners considering a similar upgrade can explore our patio screen cages in Punta Gorda.
Permitting took 2 weeks, and the work took about 3 weeks. Project #3343 was completed on April 17, 2026, and was reported at a cost of around $8,500. The cage turned the back patio into a cleaner, more comfortable outdoor living space, protected from insects and open to airflow.
Before & After


Concrete Footing for This Patio Screen Cage
A screen cage needs a solid base before any aluminum goes up. At this Punta Gorda home, our crew excavated a trench along the cage line, including a run beside the house wall, and tied the reinforcing steel inside it. The footing was built to carry the 15 × 18 ft frame, so the shape of the trench follows the shape of the cage.
The reinforcement was set in the trench before the concrete was placed, so the steel sits inside the footing instead of on top of it. Concrete gains strength over time, so the frame went up only after the footing was in place.
Once the footing was ready, the aluminum posts were anchored to it, and the frame, the roof structure, and the screen followed. The finished cage looks clean and simple; underneath it is the concrete base that supports the whole 15 × 18 ft structure.
How We Did It
Project #3343 followed the complete design-build sequence for a patio screen cage in Punta Gorda. After an on-site consultation and measurements, the team confirmed a 15 × 18 ft layout with a hip roof and a new concrete footing. The 3D visualization, site plan, and engineering plans came next, followed by the permit, which took about 2 weeks. The work took about 3 weeks, and the finished cage was completed on April 17, 2026, and moved into warranty and ongoing company support. The six stages below describe how the planning, materials, and construction came together.
Our specialist visited the Punta Gorda property to evaluate the back patio, the rear wall of the house, the roofline, and the surrounding yard. Measurements were taken for the 15 × 18 ft cage. During this stage, the homeowners selected the bronze aluminum finish, the hip roof, No-See-Um mesh, and the access door. After the scope, materials, pricing, and timeline were confirmed, the contract was finalized. This visit set the foundation for every later stage, from design to permit and installation.

Using the field measurements, the team prepared a 3D visualization, a site plan, and engineering plans for the cage. The plans show the 15 × 18 ft layout, the hip roof, the 2 × 5 SMB beams, the 2 × 4 patio members, the 5-inch gutter with its downspout, and the access door. This planning stage let the homeowners review the proportions before construction began, and it fixed how each frame member connects to the house. The same documents were used to prepare the permit application.

Once the design and engineering documentation were complete, the permit package was prepared and submitted for review. The team coordinated the site plan and engineering plans for the Punta Gorda cage, including the gutter connection and the footing location. In this project, permit review took 2 weeks. Review periods differ by property, so another project may need a different timeline.

Materials were prepared according to the engineering plans before work began at the property. The crew built the concrete footing first, then assembled the bronze aluminum frame and set the hip roof structure with its 2 × 5 SMB beams. The 5-inch Super Gutter was connected to the house, and No-See-Um mesh was fitted to the walls and roof. The access door was installed with its hardware. The work took about 3 weeks, and each step followed the engineering drawings.

After installation, the team checked the screen fit, access door operation, frame connections, anchor points, gutter, and overall finish. The completed cage covers a 15 × 18 ft patio under a hip roof, with No-See-Um mesh across the walls and roof. The homeowners could then see how the bronze frame and the screen defined the patio. Project #3343 was completed on April 17, 2026. The cage was then ready for everyday use by the family.

Following the final handover, the completed patio screen cage was placed under Screen Factory Florida’s warranty and ongoing support. The installed No-See-Um screen typically carries a manufacturer’s material warranty of about 5 years, while our team remains available to assist with questions related to the screen panels, the access door, the hardware, or other installed components. The homeowners can now enjoy a protected, screened patio with dependable support after installation.

Want a Similar Result?
Get a free estimate for your project —
we’ll call you back within 15 minutes.
Design, Permits & Project Planning
Project #3343 brought a bronze patio screen cage with a hip roof to a home on Palm Frond Dr in Punta Gorda. The structure measures 15 ft by 18 ft and stands about 11 ft high. Planning covered the hip roof, the 2 × 5 SMB beams, the 5-inch Super Gutter connection to the house, and the new concrete footing under the frame. The 3D visualization and site plan confirmed the proportions and placement before construction. Permitting took 2 weeks and the work about 3 weeks, so the project was completed on April 17, 2026.
The engineering package defined the structural requirements for the 15 × 18 ft patio screen cage, including the hip roof geometry, the 2 × 5 SMB beam layout, and the 2 × 4, 2 × 3, 2 × 2, and 1 × 2 members used in the walls and roof. It also showed the new 5-inch gutter with its 3 × 4 downspout and splash block, the access door, and the connection of the frame to the house. Each member is labeled by size on the plans, and the hatch legend marks the existing structure. The package was prepared for permit review, which took about 2 weeks. The drawings show plan, front, and side views with dimensions, and a flood zone note.

The 3D model provided a clear preview of the patio screen cage before fabrication and installation began. It showed the bronze frame, the hip roof structure, the access door, the downpipe, and how the cage connects to the house wall. Reviewing these views together with the plans helped confirm the proportions and placement before construction began. The model also shows the cage from several angles, including the front, the left side, the right side, and the top view, which made it easier to judge the layout before anything was built. The views show the 15 ft front and the 18 ft side walls clearly.

The site plan placed the new patio screen cage at the rear of the single-family residence on its lot. It shows the 15 ft by 18 ft structure, its distances to the property lines, with about 10 ft to the side line on one side, about 31.5 ft on the other, and about 31.75 ft to the rear line, and the lot outline, which measures 56 ft 6 in. by 125 ft, so the position of the structure could be checked against the boundaries. It supported permit coordination and confirmed where the cage sits on the lot before the footing was excavated. The drawing also marks the house outline next to the structure and the street, Palm Frond Dr.

Frequently Asked Questions
Answers to common questions about patio screen cages with a hip roof in Punta Gorda, including cost, permits, timelines, and maintenance.
How much does a patio screen cage with a concrete footing cost in Florida?
The cost depends on the size of the structure, the frame finish, the roof style, the screen type, the number of doors, and the foundation work. A new footing adds excavation, steel, and concrete to the scope, so a cage that needs one costs more than a frame set on an existing slab. For Project #3343 in Punta Gorda, the reported cost was around $8,500 for a 15 × 18 ft patio screen cage with a hip roof, No-See-Um screen, a 5-inch Super Gutter, and a new concrete footing. That figure describes this installation only. The most reliable way to price your own cage is an on-site visit, a measured scope, and a written estimate that lists the foundation and every feature included.
What is a hip roof on a patio screen cage?
A hip roof slopes down on its outer sides instead of ending in a vertical gable wall. On a screen cage, this gives the structure a compact, house-like profile and adds headroom in the center. On Project #3343, the roof rises about 2 ft above the 9 ft walls, for an overall height of about 11 ft, and it is covered with No-See-Um screen like the walls. Compared with a flat roof, a hip roof has more members and connections, so it needs its own engineering for each project. The members and connections depend on the span and the site, so the same shape can need different framing on another home. Ask your contractor to show the roof framing on the engineering plans before you choose a roof style.
Do you need a permit to build a patio screen cage in Florida?
In most cases, yes. A patio screen cage is a permanent structure attached to the house, and Florida counties and cities generally review it before construction, including how it connects to the house and what it stands on. Requirements differ by location, so check with the local building department or ask your contractor to confirm them for your address. For Project #3343 in Punta Gorda, permit review took about 2 weeks. Another project may take more or less time, depending on the property, the complexity of the structure, and how complete the application is when it is submitted. A contractor who prepares the site plan and engineering plans can keep the schedule clear.
How long does it take to build a patio screen cage with a new footing?
The timeline has several parts: the permit stage, the footing work, material preparation, and the installation of the frame, roof, and screen. On Project #3343 in Punta Gorda, permit review took about 2 weeks, and the work took about 3 weeks. The project was completed on April 17, 2026. A larger or more complex cage can take longer. Concrete needs time to gain strength, so a new footing adds days to the schedule compared with a frame set on an existing slab. Before you sign a contract, ask for the expected permit window and the installation schedule in writing, and ask how weather could move the dates.
How do you take care of a patio screen cage?
Rinse the screen panels and the frame with a garden hose from time to time to remove dust, pollen, and debris, and clear leaves from the roof screen so they do not hold water. Check the mesh for small tears and repair them early, because a small opening can grow. Open and close the access door to confirm that the hinges and latches move smoothly, and inspect the frame connections and fasteners after major storms. Keep the gutter and downpipe clear so water does not collect against the frame or the house wall. For questions about this installation, contact Screen Factory Florida and reference Order #3343.
More projects
Explore more screen enclosure and pool cage projects in the Florida area.
Our Services
From custom pool enclosures and screened lanais to motorized screens and hurricane shutters, we create outdoor spaces made for the Florida lifestyle. Every solution combines lasting protection, everyday comfort, and clean design – so you can enjoy more fresh air, fewer insects, and peace of mind in any weather.
Hi, I'm Alex, your project consultant. Fill in the details and I'll personally get back to you today.













