Screen Lanai in Babcock Ranch (Project #4387) – Anchorage Rd, Punta Gorda, FL
This Babcock Ranch screen lanai covers a 25 × 10 ft paver patio with a bronze aluminum frame, a mansard roof, and Super Screen mesh. It stands about 13 ft high, rests on a reinforced concrete footing, and connects to the house through a 7-inch Super Gutter. Permitting took about 2 weeks after the HOA and architectural committee approvals, and installation took about 4 weeks.
Project Overview
In Tucker’s Cove at Babcock Ranch, the homeowners wanted a screened space on their paver patio at the back of the house. Project #4387 added a new screen lanai that is 25 ft wide and 10 ft deep, with a footprint of about 250 sq. ft. and a structure area of about 705 sq. ft. The frame is bronze aluminum, and the structure stands about 13 ft high.
Building in Babcock Ranch starts with the community, not the county. Babcock Ranch is a master-planned community with its own independent special district for shared infrastructure. For this house, the project was approved by the Tucker’s Cove HOA, then by the Babcock Ranch architectural committee, and only then submitted to Charlotte County for the building permit.
A mansard roof with 2 × 6 and 2 × 9 SMB beams covers the lanai, and cable bracing stiffens the frame. A 7-inch Super Gutter connects the roof to the house and carries rain away through downpipes. Stainless steel screws and anchors resist corrosion, and the posts, beams, and bracing share one bronze finish.
A reinforced concrete footing carries the frame, and the posts are anchored through the pavers into it. Super Screen mesh covers the walls and roof. Every property needs its own measurements and estimate, so the figures here describe this installation only.
Homeowners considering a similar upgrade can explore our screen enclosures in the Punta Gorda area.
Permitting took about 2 weeks: the application was submitted on July 28, 2026, and the permit was received on August 10, 2026. Installation ran from August 24 to September 22, 2026, and Project #4387 was reported at a cost of around $7,000. The lanai turned the patio into a cleaner, more comfortable outdoor living space, protected from insects and open to airflow and daylight.
Before & After


Reinforced Concrete Footing for This Screen Lanai
A screen lanai that stands on a paver patio needs a solid base under the frame. Before the aluminum went up, our crew excavated a trench along the lanai perimeter, set the reinforcing steel, and poured a 12 × 12 inch concrete strip footing, as shown in the engineering plans for this project.
The footing details call for 3000 PSI concrete and two continuous #5 bars with 3 inches of concrete cover over the steel. The rebar was set in the trench before the concrete was placed, so the steel sits inside the footing instead of on top of it.
The aluminum posts are anchored through the pavers into the footing, with anchors that penetrate at least 2¾ inches into the concrete, as specified on the plans. A concrete door step is included at the access door. The finished surface looks clean and simple; underneath it is the reinforced foundation supporting this 25 × 10 ft screen lanai.
How We Did It
Project #4387 followed the complete design-build sequence for a screen lanai in Babcock Ranch. After an on-site consultation and measurements, the team confirmed a 25 × 10 ft layout with a mansard roof and a concrete footing. The 3D visualization, site plan, and engineering plans came next, followed by the community approvals and the county permit. Permitting took about 2 weeks, and installation ran for about 4 weeks, from August 24 to September 22, 2026. The finished lanai moved into warranty and ongoing company support. The six stages below describe how the planning, materials, and construction came together.
Our specialist visited the Tucker’s Cove property to evaluate the paver patio, the rear wall of the house, the roofline, and the yard that faces the pond. Measurements were taken for the 25 × 10 ft lanai. During this stage, the homeowners selected the bronze aluminum finish, the mansard roof design, Super Screen mesh, and the 7-inch Super Gutter connection. After the scope, materials, pricing, and timeline were confirmed, the contract was finalized. This visit set the foundation for every later stage, from design to permit and installation.

Using the field measurements, the team prepared a 3D visualization, a site plan, and engineering plans for the lanai. The plans show the 25 × 10 ft footprint, the mansard roof, the 2 × 6 and 2 × 9 SMB beams, the cable bracing, the 7-inch Super Gutter, and the 12 × 12 inch concrete footing with its anchor details. This planning stage let the homeowners review the proportions before construction began. The same documents were then used for the community approvals and the permit application.

In Babcock Ranch, the permit process starts before the county. The sequence for this house was: approval from the Tucker’s Cove HOA, then approval from the Babcock Ranch architectural committee, and then the building permit application to Charlotte County. The application was submitted on July 28, 2026, and the permit was received on August 10, 2026, about 2 weeks later. Requirements and review times differ by property and community, so confirm the current steps with your association and the county before you plan a schedule.

Materials were prepared according to the engineering plans before installation began at the property. After the footing and the paver patio were in place, the installers assembled the bronze aluminum frame, set the mansard roof structure, and anchored the posts through the pavers into the footing. The 7-inch Super Gutter was connected to the house, cable bracing was installed, and Super Screen mesh was fitted to the walls and roof. The access door was installed with its hardware. Installation ran from August 24 to September 22, 2026, about 4 weeks. Each step followed the engineering drawings.

After installation, the team checked the screen fit, access door operation, frame connections, anchor points, cable bracing, Super Gutter, and overall finish. The completed lanai covers a 25 × 10 ft patio under a mansard roof, with Super Screen mesh across the walls and roof. The homeowners could then see how the bronze frame and screen defined the patio. Installation was completed on September 22, 2026. The lanai was then ready for everyday use by the family.

Following the final handover, the completed screen lanai was placed under Screen Factory Florida’s warranty and ongoing support. The installed Super Screen typically carries a manufacturer’s material warranty of about 10 years, while our team remains available to assist with questions related to the screen panels, the access door, the hardware, or other installed components. The homeowners can now enjoy a protected, screened patio with dependable support after installation.

Want a Similar Result?
Get a free estimate for your project —
we’ll call you back within 15 minutes.
Design, Permits & Project Planning
Project #4387 brought a bronze screen lanai to a home in Tucker’s Cove at Babcock Ranch. The structure measures 25 ft by 10 ft, stands about 13 ft high, and has a mansard roof. Planning covered the 2 × 6 and 2 × 9 SMB beams, the cable bracing, Super Screen mesh, the 7-inch Super Gutter connection to the house, and the 12 × 12 inch concrete footing with anchors through the pavers. Stainless steel screws and anchors were used throughout. The project went through the HOA and architectural committee approvals before the county permit. Permitting took about 2 weeks, and installation ran from August 24 to September 22, 2026.
The engineering package defined the structural requirements for the 25 × 10 ft screen lanai, including the mansard roof geometry, the 2 × 6 and 2 × 9 SMB beam layout, cable bracing, and attachment to the house through a 7-inch Super Gutter. It also specified the foundation: a 12 × 12 inch strip footing with two #5 bars and anchors that penetrate the pavers into the footing. Each member is labeled by size on the plans, and the legend marks the cable bracing. The package was prepared for permit review, which took about 2 weeks. The drawings show plan, front, and side views with dimensions. The footing detail specifies 3 inches of concrete cover over the steel.

The 3D model provided a clear preview of the screen lanai before fabrication and installation began. It showed the mansard roof, the bronze frame, the cable bracing, the access door, the downpipes, and how the structure connects to the house. Reviewing these views together with the plans helped confirm the proportions and placement before construction began. The model also shows the lanai from several angles, including the roofline, the way the frame meets the house wall, and the door position, which made it easier to judge the layout before anything was built. The views show the compact 25 × 10 ft shape clearly.

The site plan placed the new screen lanai at the rear of the single-family residence on its lot. It shows the 25 ft by 10 ft structure, its distances to the property lines, with about 16.3 ft to the side line and about 49 ft to the rear line, the marked setback lines, and the lot outline with a north arrow, so the position of the structure could be checked against the boundaries. It supported permit coordination and confirmed where the lanai sits on the lot before the footing was excavated. These dimensions let the team verify the layout before the footing work began. The drawing also marks the house outline next to the structure.

Frequently Asked Questions
Answers to common questions about screen lanais in Babcock Ranch, including cost, permits, HOA approval, timelines, and maintenance.
How much does a screen lanai with a concrete footing cost in Florida?
The cost depends on the size of the structure, the frame finish, the roof style, the screen type, the number of doors, and the foundation work. A footing adds excavation, steel, and concrete to the scope, so a lanai that needs one costs more than a frame set on an existing slab. For Project #4387 in Babcock Ranch, the reported cost was around $7,000 for a 25 × 10 ft screen lanai with a mansard roof, Super Screen mesh, a 7-inch Super Gutter, and a reinforced concrete footing. That figure describes this installation only. The most reliable way to price your own lanai is an on-site visit, a measured scope, and a written estimate that lists the foundation and every feature included.
How do you get a permit for a screen lanai in Babcock Ranch?
In Babcock Ranch, the permit follows the community approvals. For Project #4387, the plans were approved by the Tucker’s Cove HOA, then by the Babcock Ranch architectural committee, and then submitted to Charlotte County for the building permit. The application was submitted on July 28, 2026, and the permit was received on August 10, 2026. Babcock Ranch also has an independent special district that handles shared infrastructure, while the building permit itself comes from the county. Rules and review times can change, so confirm the current steps with your HOA, the Babcock Ranch association, and the county building department.
Do you need HOA approval before applying for a lanai permit?
In a community like Tucker’s Cove, the HOA and the community architectural committee review exterior changes before the county permit is requested. For Project #4387, the approvals came first, and the county application followed. A complete package usually includes the plans, the dimensions, the colors, and the screen type, so a contractor who prepares the site plan and engineering drawings can keep the process moving. Every association sets its own rules, so ask your HOA for its current submission steps and forms before you sign a contract. Waiting for the approvals before ordering materials helps avoid changes later. County approval does not replace the community approvals, and community approval does not replace the county permit.
How long does it take to get a screen lanai approved and built?
The timeline has several parts: the community approvals, the county permit, the footing work, and the installation of the frame and screen. On Project #4387, the county permit took about 2 weeks, from the application on July 28, 2026, to the permit on August 10, 2026, and installation ran from August 24 to September 22, 2026, about 4 weeks. A larger or more complex lanai can take longer. The HOA and architectural committee reviews add time before the county application, and they vary by community. Before you sign a contract, ask for the expected approval and permit windows and the installation schedule in writing, and ask how weather could move the dates.
How do you take care of a screen lanai on a paver patio?
Rinse the screen panels and the frame with a garden hose from time to time to remove dust, pollen, and debris. Check the mesh for small tears and repair them early, because a small opening can grow. Open and close the access door to confirm that the hinges and latch move smoothly, and inspect the frame connections and fasteners after major storms. On a paver patio, keep the joints between the pavers and the base of the posts clear of dirt and weeds. Keep the gutter and downspouts clear so water does not collect against the frame. For questions about this installation, contact Screen Factory Florida and reference Order #4387.
More projects
Explore more screen enclosure and pool cage projects in the Florida area.
Our Services
From custom pool enclosures and screened lanais to motorized screens and hurricane shutters, we create outdoor spaces made for the Florida lifestyle. Every solution combines lasting protection, everyday comfort, and clean design – so you can enjoy more fresh air, fewer insects, and peace of mind in any weather.
Hi, I'm Alex, your project consultant. Fill in the details and I'll personally get back to you today.



















