Screen Patio Enclosure with IRP Roof (Project #4776) – Isaac Ln, Punta Gorda, FL
This Punta Gorda screen patio enclosure covers a 38 × 14 ft patio with a bronze aluminum frame, a 3-inch IRP roof, and Super Screen mesh. It stands about 9 ft 6 in. high and uses 2 × 4 SMB beams, cable bracing, a 16-inch kick plate, and an E-Gutter with downpipes. The permit stage took about 10 days, and installation took about 4 weeks.
Project Overview
At a home on Isaac Ln in Punta Gorda, the homeowners wanted a screened, covered space on their back patio. Project #4776 added a new screen patio enclosure that is 38 ft wide and 14 ft deep, with a footprint of about 532 sq. ft. The frame is bronze aluminum, and the structure stands about 9 ft 6 in. high.
The roof is an IRP, an insulated roof panel system. The 3-inch white panels have an EPS core and are laid with a minimum slope of 1/4 inch per foot, as specified on the engineering plans, so rain runs off toward the gutter. Under the roof, the patio gets shade and a finished ceiling look, with less rain noise than a single aluminum panel.
The frame uses 2 × 4 SMB beams and cable bracing, and a 16-inch kick plate runs along the base of the walls. An E-Gutter along the 38 ft front edge collects rain, and downpipes carry it away. At the house wall, a 7-inch Super Gutter handles the connection of the roof panels.
Super Screen 17/20 mesh covers the walls, keeping out insects while keeping airflow in the space, and the access doors are fitted with bronze hardware. The posts are anchored to the existing foundation, so no new footing was needed. Every property needs its own measurements and estimate, so the figures here describe this installation only.
Homeowners considering a similar upgrade can explore our patio screen enclosures in Punta Gorda.
Permitting took about 10 days: the application was submitted on September 11, 2026, and the permit was approved on September 21, 2026. Installation ran from September 23 to October 20, 2026, and Project #4776 was reported at a cost of around $19,000. The enclosure turned the back patio into a cleaner, more comfortable outdoor living space, protected from insects, shaded by the insulated roof, and open to airflow.
Before & After


See How This Punta Gorda Screen Patio Enclosure Came Together
Step inside Project #4776 and see how this Punta Gorda back patio became a screened outdoor room. The project is a 38 × 14 ft enclosure with a 3-inch IRP roof, 2 × 4 SMB beams, cable bracing, an E-Gutter with a 7-inch Super Gutter connection, Super Screen mesh, and access doors. Watch how the finished enclosure protects the patio from insects and rain while keeping the space open to airflow.
How We Did It
Project #4776 followed the complete design-build sequence for a screen patio enclosure in Punta Gorda. After an on-site consultation and measurements, the team confirmed a 38 × 14 ft layout with an IRP roof. The 3D visualization, site plan, and engineering plans came next, followed by the permit. Permitting took about 10 days, and installation ran from September 23 to October 20, 2026. The finished enclosure was completed on October 31, 2026, and moved into warranty and ongoing company support. The six stages below describe how the planning, materials, and construction came together.
Our specialist visited the Punta Gorda property to evaluate the back patio, the rear wall of the house, the roofline, and the surrounding yard. Measurements were taken for the 38 × 14 ft enclosure. During this stage, the homeowners selected the bronze aluminum finish, the IRP roof, Super Screen mesh, and the access doors. After the scope, materials, pricing, and timeline were confirmed, the contract was finalized. This visit set the foundation for every later stage, from design to permit and installation.

Using the field measurements, the team prepared a 3D visualization, a site plan, and engineering plans for the enclosure. The plans show the 38 × 14 ft layout, the 3-inch IRP roof panels, the 2 × 4 SMB beams, the cable bracing, the E-Gutter and Super Gutter connection, and the 16-inch kick plate. This planning stage let the homeowners review the proportions before construction began, and it fixed how each frame member connects to the house and the existing foundation. The same documents were used to prepare the permit application.

Once the design and engineering documentation were complete, the permit package was prepared and submitted for review. The team coordinated the site plan and engineering plans for the Punta Gorda enclosure, including the roof panel and anchor details. The application was submitted on September 11, 2026, and the permit was approved on September 21, 2026, about 10 days later. Review periods differ by property, so another project may need a different timeline.

Materials were prepared according to the engineering plans before installation began at the property on September 23, 2026. After the plans were confirmed on site, the installers assembled the bronze aluminum frame, set the 2 × 4 SMB beams, and anchored the posts to the existing foundation. The 3-inch IRP roof panels were installed together with the gutters and downpipes, cable bracing was added, and Super Screen mesh was fitted to the walls. The access doors were installed with their hardware. Installation was completed on October 20, 2026. Each step followed the engineering drawings.

After installation, the team checked the screen fit, access door operation, frame connections, anchor points, cable bracing, gutters, and overall finish. The completed enclosure covers a 38 × 14 ft patio under an insulated IRP roof, with Super Screen mesh across the walls. The homeowners could then see how the bronze frame and the white roof panels defined the patio. Project #4776 was completed on October 31, 2026. The enclosure was then ready for everyday use by the family.

Following the final handover, the completed screen enclosure was placed under Screen Factory Florida’s warranty and ongoing support. The installed Super Screen typically carries a manufacturer’s material warranty of about 10 years, while our team remains available to assist with questions related to the screen panels, the access doors, the hardware, or other installed components. The homeowners can now enjoy a protected, screened patio with dependable support after installation.

Want a Similar Result?
Get a free estimate for your project —
we’ll call you back within 15 minutes.
Design, Permits & Project Planning
Project #4776 brought a bronze screen patio enclosure with an IRP roof to a home on Isaac Ln in Punta Gorda. The structure measures 38 ft by 14 ft and stands about 9 ft 6 in. high. Planning covered the 3-inch EPS roof panels and their minimum slope, the 2 × 4 SMB beams, the cable bracing, the E-Gutter and 7-inch Super Gutter connection to the house, and the anchors to the existing foundation. The 3D visualization and site plan confirmed the proportions and placement before construction. Permitting took about 10 days, and installation ran from September 23 to October 20, 2026, so the project was completed on October 31, 2026.
The engineering package defined the structural requirements for the 38 × 14 ft screen patio enclosure, including the 3-inch EPS roof panels with a minimum slope of 1/4 inch per foot, the 2 × 4 SMB beam layout, cable bracing, the 16-inch kick plate, and attachment to the house through a 7-inch Super Gutter. It also showed the E-Gutter along the front edge and the anchors that fix the posts to the existing foundation. Each member is labeled by size on the plans, and the legend marks the cable bracing. The package was prepared for permit review, which took about 10 days. The drawings show plan, front, and side views with dimensions.

The 3D model provided a clear preview of the screen patio enclosure before fabrication and installation began. It showed the bronze frame, the white IRP roof, the 16-inch kick plate, the screen walls, and how the structure connects to the house. Reviewing these views together with the plans helped confirm the proportions and placement before construction began. The model also shows the enclosure from several angles, including the front, the left side, the right side, and the top view, which made it easier to judge the layout before anything was built. The views show the long 38 ft wall clearly.

The site plan placed the new screen patio enclosure at the rear of the single-family residence on its lot. It shows the 38 ft by 14 ft structure, its distances to the property lines, with about 21 ft to the side lines on both sides and about 40 ft to the rear line, the marked easements, and the lot outline, which covers about 0.23 acres, with a north arrow, so the position of the structure could be checked against the boundaries. It supported permit coordination and confirmed where the enclosure sits on the lot before installation. The drawing also marks the house outline next to the structure and the street, Isaac Lane.

Frequently Asked Questions
Answers to common questions about screen patio enclosures with an IRP roof in Punta Gorda, including cost, permits, timelines, and maintenance.
How much does a screen patio enclosure with an IRP roof cost in Florida?
The cost depends on the size of the structure, the frame finish, the roof system, the screen type, the number of doors, and the condition of the foundation. An IRP roof uses insulated panels, which cost more than a plain aluminum roof panel and need more exact engineering. For Project #4776 in Punta Gorda, the reported cost was around $19,000 for a 38 × 14 ft screen patio enclosure with a 3-inch IRP roof, Super Screen mesh, cable bracing, and an E-Gutter with downpipes. The posts were anchored to an existing foundation, so no new footing was part of the work. That figure describes this installation only. The most reliable way to price your own enclosure is an on-site visit, a measured scope, and a written estimate.
What is an IRP roof on a screen enclosure?
IRP stands for Insulated Roof Panel. It is a sandwich panel with two aluminum sheets and insulation between them, so it gives more shade, less rain noise, and a more comfortable temperature under the roof than a single non-insulated panel. From inside, it looks like a finished ceiling. On Project #4776, the engineering plans specify 3-inch panels with an EPS core, installed with a minimum slope of 1/4 inch per foot so rain runs off to the gutter. An IRP roof suits a patio that is used as a living space, but it costs more and needs more exact engineering than a standard panel roof. Ask your contractor how the panels will be supported and drained.
Do you need a permit to build a screen patio enclosure in Florida?
In most cases, yes. A screen patio enclosure is a permanent structure attached to the house, and Florida counties and cities generally review it before construction, including how it connects to the existing foundation. Requirements differ by location, so check with the local building department or ask your contractor to confirm them for your address. For Project #4776 in Punta Gorda, the application was submitted on September 11, 2026, and the permit was approved on September 21, 2026, about 10 days later. Another project may take more or less time, depending on the property, the complexity of the structure, and how complete the application is when it is submitted. A contractor who prepares the site plan and engineering plans can keep the schedule clear.
How long does it take to build a screen patio enclosure with an IRP roof?
The timeline has several parts: the permit stage, material preparation, and the installation of the frame, roof panels, and screen. On Project #4776 in Punta Gorda, permitting took about 10 days, and installation ran from September 23 to October 20, 2026, about 4 weeks. The project was completed on October 31, 2026. A larger or more complex structure can take longer. Before you sign a contract, ask for the expected permit window and the installation schedule in writing, and ask how weather could move the dates. An existing foundation, as on this project, shortens the work compared with a build that needs new concrete.
How do you take care of a screen enclosure with an IRP roof?
Rinse the screen panels and the frame with a garden hose from time to time to remove dust, pollen, and debris. Check the mesh for small tears and repair them early, because a small opening can grow. Rinse the white roof panels the same way, and keep the gutter and downpipes clear so water does not collect on the roof or against the frame. Open and close the access doors to confirm that the hinges and latches move smoothly, and inspect the frame connections, cable bracing, and fasteners after major storms. For questions about this installation, contact Screen Factory Florida and reference Order #4776.
More projects
Explore more screen enclosure and pool cage projects in the Florida area.
Our Services
From custom pool enclosures and screened lanais to motorized screens and hurricane shutters, we create outdoor spaces made for the Florida lifestyle. Every solution combines lasting protection, everyday comfort, and clean design – so you can enjoy more fresh air, fewer insects, and peace of mind in any weather.
Hi, I'm Alex, your project consultant. Fill in the details and I'll personally get back to you today.














